St. Petersburg, warm water, flowing gas water heater NEVA Suite. In summer everything is fine in casa view plumbing, but in winter the incoming water is much colder and does not have time to heat up. For the shower, it is quite comfortable, but to take a bath, to steam out, it is completely lacking. You have to heat the water in the pots and need to some fix through accomplish learned support out of possession of to ensure casa view plumbing.
The solution I see is this: on the wall in the bathroom I hang up an additional flow-through electric heating and I connect the shower hose from the mixer to it. It is necessary to type a bath – turn on additional heating. For the summer – removed, put in the pantry.
That is the task – just add about 5-10 degrees to the temperature of the water. Most power is not needed, the washing machine / iron / kettle / dishwasher included together knock out the dispensers.
I would like to ask knowledgeable people what the problems may be and whether this scheme is working in principle. It is unlikely that I was the first to encounter such a task.
Good evening. We live in a five-story house on the fifth floor with hot water supply, feed from below. Already about 3 months from the hot water tap flows either cold or lukewarm water. The same picture on floors 3-4. Water temperature varies from 30 ° C to 40 ° C approximately. At the top of the return pipe we have a crane, so the system is not airy. In the Criminal Code they say that most likely there is some kind of operation on the lower floors, but they do not like it, we can’t do anything, the 1st and 2nd floors are not allowed into the apartment, but on the first floor there is a heated towel rail and hot water, just like in the basement riser, and on the second floor – boiler. I, as I could, drew an approximate scheme
The water does not drain at all and even when I turn on the hot water tap, the towels almost immediately become cold, and the water goes warm, the water pressure is normal. Please tell me, what could be the problem in principle?
The apartment has some kind of ancient mixer somehow cleverly attached. I myself am not a boom boom, maybe it is attached as standard. Tell me, is it suitable for any one on sale or should it be chosen specifically for this mount? And will this mount fall apart if you start to unscrew it?
In the second photo (toilet), the left mount is located behind the door along with the entire water system and meters, and the right one is for some reason outside the door. The door is not visible, it is open.
There Khrushchev, enter HGV made 20m polypropylene. Risers are old, the pressure is not so hot, when consumers turn on the pressure drop is quite noticeable. . There is a desire to collect a collector and try to solve this problem. Consumers -3 (kitchen, bath, toilet). The collector makes 25 pipe, with taps at 20. Is there any reason for this if the inlet pipe is still 20 diameters? Familiar santeh says that I suffer from garbage. Tell me plz, is it worth bothering, or is the sense from such a collector zero and is it easier to collect everything and not bathe according to the tee scheme?
I ask to help with a solution of a problem with a pressure from a watering can. The Hansgrohe Metris 31480000 mixer and Hansgrohe Croma Select shower head are installed. Both are in use for a short time, about six months.
In the shower watering canal, the pressure was, of course, “not super,” but quite tolerable. Last week, the pressure dropped significantly (with hot water more significantly, with cold – to a lesser extent). What pressure is now visible on the video link? In this case, as can be seen, the water from the tap in the mixer comes with a normal pressure.
He took off the hose, opened the water directly from the mixer while holding the switch to the shower – the water goes as if spitting – the jet goes not smoothly, but is sprayed with a cone. I suspect that the problem may be at this point where the hose is connected to the tap. There is something like a black plastic sleeve, tried to unscrew it with a casa view plumbing key, but did not understand which way to turn and besides, it seems very flimsy, as if not to break it because 100% not sure where to turn.
Can anyone come across this problem and help with advice for casa view plumbing?